| SMALL DIAMETER GEO-SUPPORT DESIGN & CONSTRUCTION SEMINAR |
$525.00 ADSC/DFI Member
$625.00 Non-Member
$195.00 Government Employee/Student
What’s included with your Registration?
Photograph Release: By submitting the registration form, you hereby release any photographs that may be incidentally taken of me during these events by Seminar Management to be used for any purpose.
Liability Waiver:
By submitting the registration form, you are are agreeing and acknowledging the following: I am undertaking participation in ADSC/DFI Small Diameter Geo-Support Design and Construction Seminar and activities at my own free and intentional act, and I am fully aware that possible physical injury might occur to me as a result of my participation. I give this acknowledgement freely and knowingly that I am, as a result, able to participate in ADSC/DFI Small Diameter Geo-Support Design and Construction Seminar events, and I do hereby assume responsibility for my own well-being. I also agree not to allow any other individual to participate in my place without prior permission from the Seminar Management.
GENERAL INFORMATION
13869 Park Center Road
Herndon, VA 20171
A special discounted guest room rate for this seminar is $159 + tax. Make reservations early to secure your room. Space and rate are subject to availability. Cut-off date for discounted rate is October 22, 2012. The special rate will also be honored 3 days prior /3 days following the seminar, based on availability. Cancellation of Guest room within 72 hours of arrival will incur a one night’s room and tax charge.
To make reservations, call 703-478-2900 or 800-422-0873 and advise you are attending the ADSC/DFI Small Diameter Geo-Support Design & Construction Seminar.
Early Departure… Should you check out prior to your schedule departure date, the hotel will add a $50.00 fee to your hotel bill. To avoid this, please advise the hotel at the time of your check in that you are departing early.
TRANSPORTATION
Dulles International Airport (airport code: IAD) is three miles from the Hilton Washington Dulles Hotel and 28 miles from Washington Ronald Regan National Airport (airport code is DCA).
Taxi's are readily available at both airports and one way fee is approximately $9.00 from Dulles Airport and $50.00 from Washington Ronald Regan National (subject to change without notice).
Driving Directions
From Washington, D.C.
Interstate 66 West merge onto VA-267 W Dulles Toll Road via exit 67 toward DULLES AIRPORT (9 Miles). From the Dulles Toll Road, take Exit 9A, Route 28 South/Centreville (15 Miles). Exit at McLearen Road (3 Miles), turn left at 1st light on Towerview and make 1st left on Park Center Road. Follow 0.1 mile, the hotel is on your left.
From Baltimore and All Points North
From Interstate 95 South merge onto CAPITAL BELTWAY/I-495 W EXIT 27 toward Tysons Corner, VA. Merge onto VA-267 W Dulles Toll Road via exit 45A toward DULLES AIRPORT. From the Dulles Toll Road, take Exit 9A, Route 28 South/Centreville (12 Miles). Exit at McLearen Road, turn left at 1st light on Towerview and make 1st left on Park Center Road. Follow 0.1 mile, the hotel is on your left.
From Richmond and All Points South
From Interstate 95 North merge onto Dumfries Road/VA-234 N via EXIT 152 B toward MANASSAS (14 Miles). Turn right onto Liberia Avenue/Prince William Parkway/VA-3000 N (4 Miles). Turn right onto VA-28 N/Centreville Road. Proceed 12.5 miles, exit at McLearen Road, turn left at 1st light on Towerview and make 1st left on Park Center Road. Follow 0.1 mile, the hotel is on your left.
From Interstate 81 and All Points West
From I-66 East toward Washington, DC. Merge onto Sully Road/VA Route 28 N via EXIT 53 toward DULLES AIRPORT. Proceed 8 miles and exit at McLearen Road, turn left at 1st light on Towerview and make 1st left on Park Center Road. Follow .1 mile, the hotel is on your left
You may earn up to 15.25 PDHs. This form is for your benefit and should be kept with your personal records. In recognition of the fact that an increasing number of professional engineering licensing bodies require members to pursue professional development on a formal basis, this certificate is accepted by most state professional engineering licensing bodies as documentation of your pursuit of continuing education requirements. There are, however, some states that may not accept the general Certificate.
Attendees will receive a certificate verifying Professional Development Hours (PDH)*
*New York State approval pending | *Florida State provider #4072
With respect to our seminar materials, flash drives with the speaker presentations will be issued prior to the start of the seminar.
